联系我们
CONTACT US
CONTACT US CONTACT US

CONTACT US

1

0086-755-84019605

1

0086-755-89342809

Technical Support

UNIT Conversion Chart

 

UNIT 0F TORQUE
gf·cm
kgf·cm
N·m
mN.m
N.cm
lb.in
oz.in
gf.cm
1
0.001
0.000098
0.098
0.0098
0.000868
0.013889
kgf.cm
1000
1
0
98
9.8
0.868
13.889
N.m
10200
10.2
1
1000
100
8.85
141.64
mN.m
10.2
0.0102
0.001
1
0.1
0.00885
0.142
N.cm
102
0.102
0.01
10
1
0.0885
1.42
ib.in
1152
1.152
0.113
113
11.3
1
16
oz.in
72
0.072
0.00706
7.06
0.706
0.0625
1

 

How to choose the right motor from our series?

 

---The best way is: you send us your dimension and performance requirements, and we will evaluate it and offer the best recommendation. In this situation, please let us know the following basic performance:

 

● Rated Voltage.

● Rated speed and rated torque.

● Motor using conditions: such as seconds/minutes on and seconds/minutes off, or something similar.

● will the motor be used in stall condition? this is a very important factor, if you have this condition, please make sure to let us know.

● Any extremely high or low temperature requirements.

● Any others special requirements, the more detailed the better.

---If you would like choose from our web-catalogue yourself, here are some directions that might be helpful for you:

 

● High Speed requirement: when your speed is >1300rpm, please see our Miro DC Motor(DCM series).

● Low speed and medium high torque, for example 1-1300rpm and torque from 0.3-50kg.cm, you may turn to Round Spur Gear Motor(SGM Series).

● Low speed and high torque, for example 1-100rpm speed and 20-500kg.cm torque, you may turn to Flat Spur Gear Motor(FGM sereies).

● Low speed and medium high torque and small diameter(precise and high cost), for example 0.3-1300rpm and 0.2-60kg.cm, you may turn to Planetary gear motor(PGM). This series are high cost and precise motors.

 

When use Dc Motor, please pay attention to the following:

 

Installation: The standard fasten direction is to set the shaft in horizontal direction, to change the direction may cause the oil leaking, and also cause the load direction changing, this may influence the motor performance and lifetime.

 

Shaft Machine: Do not machine the motor shaft without getting information from us, this may cause the damage of gear and gears cooperation.

 

Run the shaft(DC Gear Motor): Do not turn the shaft by hand when adjust the install direction, this will turn the gearbox to be an increaser not a reducer, and also this will turn the Dc Motor to be Generator.

 

Terminal Welding: When welding the terminal with wires, please use the Iron temperature at 350~400°C  within 2-3 seconds. Too high temperature or too long time will cause damage to motor terminal and connection parts, especially when it is metal Brushed motor.

 

Stall or overload: The Winding and Iron will create heat during motor running, and this heating will gradually increase, under normal load, the temperature can be balance between creating and releasing, it will not burn the motor winding. But if often use the Stall or Overload, the temperature can not be balance as normal, it will gradually burn the Resistant Layer over the Winding, then cause the winding to be burnt down.

 

Low Speed running: For Carton Brushed Motor, during the working of motor, the carbon Brush will be gradually wore off, and the carbon Powder will be rub off the brush. So if the motor is in lower speed, the carbon power will accumulate in the Commutator slots, when the quantity increases, it will cause the motor to be short circuit. To avoid this situation, we use different kinds of technics and materials according to different motor and speed, so it is very important that users let us know their working voltage of the motor.

 

Noise Solution: When you have strict requirements on noise and Electromagnetic Interference, please inform us in advance, we have ways to handle these issues.

 

Inertia and Solution: When the power is cut off, the motor will continue to run for a few seconds, we call this Motor Phenomenon. All the DC Motors have such Phenomenon. If you want solve this issue, you just need to connect the motor “+” to “-“, then this phenomenon will disappear. This is to use Motor-Generator Features(Inverse Current), however this action will cause a high momentary current, usually perform this action will shorten the Motor lifetime.

 

Life time: DC Motor lifetime varies according to different use conditions and load, so different working condition will cause different lifetime for the same motor, please let us know your exact using condition, we will design the motor according to it.

 

The following factors will affect the motor lifetime, so if you use motor in such condition, please inform us, we can discuss over it and try to find a solution together.

 

◆ use motor under bigger load than rated one

◆ frequently start and stop

◆ CW and CWW running transfer fast and frequently

◆ use sudden big load, not constant load

◆ long-time continuous running

◆ force the shaft to anti the running direction

◆ frequently use stall condition

◆ use lower or higher voltage than rated one

Copyright ©Etonm Motor Co., Limited.  粤ICP备15002344号    SEO Tab Navigation